You can only apply oil when it is dry and free from excess water. During application, make sure you aim directly at each pleat while applying the oil. Whatever the application method you adopt; this is determined by the type of oil container that comes with your air filter, make sure the oil is applied uniformly and adequately. In some cases, the oil comes in a squeeze can or bottle, and it can also come in a spray bottle or can. For the squeeze bottle, you should apply the oil over the pleats by squeezing out the content and placing the tip of the bottle on the pleat one after the other.
With the red dye that is contained in the oil, the areas sprayed are covered in red. So, to ascertain uniform application, the filter must be completely covered in red. After application, make sure you clean off surplus oil. To avoid wastage, you can direct excess oil from the edges of the air filter to the pleats. Ensure even distribution. The application should be done in a place where there is adequate air, preferably outside the house.
When the oil is adequately and uniformly applied across the surface of your air filter, it enables the filter to hold the particles that may try to force their way into the air intake during installation.
Asides from that, the oil as well acts as anti-rust, thereby improving the lifespan of the air filter. Once installed, do not forget to clip back the parts that secure the filter. With proper maintenance of your air filter, the engine of your vehicle is enhanced. You can confidently cover up to 50, miles of fun rides. You can spray the two sides of the filter.
Makes sure you only spray upon confirmation that the filter is dry and free of excess water. We advise that you should always have a check on the filter for every twenty-five thousand 25, miles you cover. If there are ring clamps or latches holding the filter in place, disengage them and lift the filter straight out.
The methods used to clean the filter will be the same regardless of its design. Determine whether your filter needs cleaning.
If you can still plainly see the pleats on your filter, it may not need to be cleaned, even if it appears dirty. Shake off loose dust and dirt. Give the filter a gentle shake to dislodge whatever debris is resting on the surface. Don eye protection and a breathing mask if you have them to avoid inhaling dust particles. Be careful not to shake the filter too hard or handle the pleats directly, as this could potentially damage them. Spray the filter with cleaning solution.
Grab the bottle of aerosol cleaner that came included with your filter. Spray the filter liberally on both sides. Make sure each individual pleat has been thoroughly misted with cleaner. Allow the solution to soak on the filter for 10 minutes. As the cleaner sits on the filter, it will begin to cut through caked-on grime, making it easy to rinse away.
Place the filter in the sink or on a towel while the cleaning solution does its job. This will prevent dissolved gunk from running off and staining your work surface. Part 2. Rinse the filter from the inside out with cool water. Turn on a hose or tap to a light stream. Hold the air filter directly under the stream so that the water runs through the inside of the filter to the outside. The water will carry away the dust and dirt loosened by the cleaning solution.
Shake off the excess water. Alternatively, you can rest the filter against another object at an angle and let it drip-dry. Get off as much standing moisture as you can. Again, try not to handle the filter too roughly.
For quicker drying, make sure you leave the filter in a well-ventilated area at a mild temperature. When cleaning your car's air filter, it's important to use a cleaner that will thoroughly remove dirt and debris without petroleum-based chemicals, which can damage or dissolve the filter materials. You should avoid using solvents or kerosene for this reason. Simple Green All-Purpose Cleaner is aggressive on grease and heavy soils but is gentle enough to clean air filters without harming the filter material or causing damage to surfaces found on automotive equipment.
When used per label instructions, it's safe on aluminum, chrome, titanium, and other high-tech alloys, as well as painted and gel-coated surfaces, anodized and electroplated parts, carbon fiber, metals, plastics, rubber and much more. Check your Owner's Manual before cleaning the air filter.
Always follow the manufacturer's complete instructions for cleaning and maintenance. Make sure the engine is cool to the touch before cleaning.
Industrial International. Start in the middle of the filter and make two or three passes around the middle of the filter, applying the oil. Repeat this same process in even spaces to the top and bottom of the filter to ensure an even coat while making sure not to over oil the air filter. Then, allow the oil to seep into the filter for 20 to 30 minutes. Allow the oil to dry and then inspect the filter, checking for white areas to find spots the oil missed.
If you find any, use the applicator to apply a small amount of oil to these spots and let dry. Once the oil has completely dried on the filter, use your screwdriver to remount the filter. Wipe the surface of the seal with a clean cloth once installed. Keeping your cold air intake filter clean and well maintained will improve your vehicle's fuel efficiency and help your engine to perform better for longer.
New Cars. Buyer's Guide. Type keyword s to search. Today's Top Stories. Education Images Getty Images. Types of Cold Air Intake Filter Cleaners There are three types of cold air intake filter cleaners you can choose from. The spray contains a degreasing agent which helps to quickly dissolve the grime and buildup on your filter.
0コメント